| # |
Location |
Detail |
Description |
| J1 |
 |
 |
Connection to the power supply. Either the output of a 7V-10V transformer, or a wall adapter can be used. 500 mA is recommented, especially if a backlit display is used, but MIDIfilter and MIDImerger work also with ca. 100 mA. AC or DC doesn't matter, since the rectifier behind J1 converts to DC anyhow. Also the polarity has not to be taken into account. |
| J2 |
 |
 |
+5V output, can be used to supply other core modules in a multiprocessor environment, so that you only have to mount the parts for the power supply (BR1, IC3, C5, C6) on one core module. Restriction: the 7805 gets very hot when it delivers currents above 500 mA, so only core modules without backlit display like MIDIO128, MIDImerger, MIDIfilter should be supplied over this port.
|
| J4 |
 |
 |
Interface to the BankStick, to MBHP_IIC_* modules like MBHP_IIC_MIDI, and to the second MIDI IN port for MIDImerger. |
| J5, J5A J5B |
 |
 |
This is an either-or setup. J5 matches the old (SIL) AIN connection. J5A and J5B match the with newer AIN boards (AIN_R3 up). Obviously with newer AIN boards leave out the SIL pinheader out and load J5A/B, if using older boards leave out J5A/B and load J5. Interface to the AIN module for MIDIbox64 and MIDIbox64E. There are also some application which use this as digital in- or output. |
| J6/J7 |
 |
 |
J6:Interface to the AIN module for MIDIbox64 and MIDIbox64E.
J7:Interface to the MF module, sometimes also used for the MBHP_AOUT or MBHP_AOUT_LC module.
|
J8/J9 |
 |
 |
Pay attention to this one, it has moved since last rev....
J8:Interface to the DOUT module chain.
J9:Interface to the DIN module chain.
|
J10 |
 |
 |
Pay attention to this one, it has moved since last rev....Do not mistake it for J8/J9 since they were in this position on the last rev!
J10:Interface to application specific module extensions like the SID module.
|
J11 |
 |
 |
MIDI digital IO port, interface to the LED/Thru/COM module. Can also be used to cascade multiple core modules in a long MIDI chain. Note: Don't plug the optocoupler (IC2, 6N138) into the socket when using the J11:MI (MIDI-IN) pin as an input, otherwise the Rx input will get the data from two different sources, which is not provided by the MIDI protocol (point-to-point). A MIDImerger is necessary to combine multiple MIDI IN sources.
In other words: when using the COM module or when connecting the J11:MO of one core module to J11:MI of another core module, or when connecting the core module directly with the Gameport, the optocoupler of the other module should not be plugged into the socket to avoid a corrupted MIDI data stream.
|
J12 |
 |
 |
MIDI OUT port.
This is an either-or position, load SIL 3 pin header for wiring to panel mount MIDI jacks, otherwise install a PCB mount MIDI socket in/over the J12 pads.
|
J13 |
 |
 |
MIDI IN port.
This is an either-or position, load SIL 3 pin header for wiring to panel mount MIDI jacks, otherwise install a PCB mount MIDI socket in/over the J12 pads.
|
J14 |
 |
 |
Used by MIOS as touch sensor strobe line. Sometimes also used for debugging purposes.
|
J15 |
 |
 |
Interface to LCD display module.
|
GND LIFT |
 |
 |
Can be used to temorarily disconnect the CORE's ground from the ground on J12:Pin2. Leave this alone for normal operation!
|
